Technical Information agricultural and construction engine Spray Paint
ColorMatic agricultural and construction engine acrylic spray paint is a premium, high-finished acrylic coat with high-finish - specially formulated for quick coating of industrial surfaces. Thanks to the broad-jet atomization, it can also be used on larger surfaces. An extremely high content of pigments and specific additives provides high coverage, high film thickness, good hold and good adhesion direct on metal.
To best prepare, thoroughly clean the surface to be painted with ColorMatic Silicone Remover no. 174469 and, as required, apply a primer or filler (e.g. ColorMatic 2K Primer Filler no. 195 327). In addition, we recommend the use of ColorMatic Spot Blender no. 114 229 for spot repair on edges.
Ideal for spot repairs and refinishing parts
Physical and chemical data
- Basis of binder: Acrylic
- Colour: Specific
- Smell: solvent
- Degree of gloss: (at measurement angle 60° acc. to DIN 67530)
glossy: 80 gloss units
Depending on consistence and colour of the ground:
400 ml are sufficient for approx. 0,8 - 1,0 m²
ColorMatic 2K Primer Filler no. 195 327
ColorMatic 1K Primer for Aluminium no. 190 278
ColorMatic 1K Primer for Zinc no. 190 285
ColorMatic 1K Epoxy Primer no. 174 414
ColorMatic 1K Filler, beige no. 856 556
ColorMatic 1K Filler, grey no. 874 987
Cured paint, polished
- ColorMatic 1K Primer Filler:
HG 1 white no. 856 532
HG 2 light grey no. 882 425
HG 3 grey no. 856 525
HG 4 tele grey no. 644 719
HG 5 basalt grey no. 882 432
HG 6 graphite grey no. 882 449
HG 7 black no. 549 663
HG 8 red no. 856 549
- Drying time (at 20°C, 50% relative air humidity):
Dust-dry: after approx. 10 Minuten
Dry to touch: after 30 minutes
The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
- Temperature resistance: to 90°C
- Storage stability:
10 years if appropriabte storage provided (=10°-25°C, relative air humidity of max. 60%)
Aerosol cans, maximum nominal volume 400 ml
- VOC-value: 272,7 g
Environment and labelling
Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.
Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse".
Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,
- Clean surfaces to be painted thoroughly with ColorMatic silicone remover no. 174469, then sand
- The area must be dry and free of dust and grease
- Shake can well for 2 minutes
- Carry out spray test
- 2-3 coats
- For professional use only
- Wear an appropriate respirator (recommended type A2/P3)
Disclaimer of liability
This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.
For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.
As of October 05, 2011
This release replaces all eventually earlier issued versions