Technical Information 1K Clear Coat

Technical Information 1K Clear Coat

ColorMatic 1K clear coat is a UV-resistant, fast-drying clear coat that can be applied universally at all existing base coats (solvent-based). Available in glossy, satin gloss and mat quality. Because of its very good flow and ease of polish, 1K Clear Coat glossy is highly suitable for spot repairs with solvent-based paints (e.g. ColorMatic solvent-based).

For best preparation of the surface which is to varnish, clean it thoroughly with ColorMatic Silicone Remover no. 174469 and, if required, apply a primer or filler  (e.g. ColorMatic 2K Primer Filler no. 195327). We recommend using ColorMatic Spot Blender no. 114229 for spot repair on the edges.

glossy: ideal for spot repairs and refinishing parts.
satin gloss and mat: painting of construction parts with mat look.

Quality and properties

  • Fast drying time
  • Easy application
  • Can be used on all solvent-based paints
  • UV resistant

    Especially at 1K Clear Coat glossy:
  • Highly suited for spot repairs due to good flow and being easy to polish
  • Light blending
  • High gloss

    Especially at 1K Clear Coat satin gloss and mat:
  • Ideal for all construction parts with a brilliant mat respectively satin gloss look
  • Tip: we advice at Clear Coat mat to paint the construction parts complete
  • Caution: don't polish!

Physical and chemical data

  • Basis of binder: Acrylic resin
  • Colour: transparent
  • Smell: solvent
  • Degree of gloss: at measurement angle 60° acc. DIN 67530
    glossy: 85 - 90 GE
    satin gloss: 60 GE
    mat: 10 (+/- 5) GE
  • Efficiency:
    Depending of consistence and colour of the substrate 400 ml are sufficient for approx. 1,5 - 2,0 m²   
  • Substrate:
    Basecoats uni or metallic
  • Drying (at 20°C, 50% relative air humidity):
    Dust-dry: after 5 - 10 minutes
    Touch-dry: after 10 - 20 minutes
    Cured after 24 hours
    The drying time is depending on the ambient temperature, air humidity and the applied paint layer
  • Temperature resistance:
    glossy to 110°C
    mat to 80°C
  • Storage stability:
    10 years if appropriate storage provided
  • Size:
    Aerosol cans, maximum nominal volume 400 ml
  • VOC-Value:
    glossy 276,4 g
    satin gloss 271 g
    mat 253,9 g



Environment and labelling

Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". 

Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, 

Using instructions

Before use, carefully read and observe the warning texts on the label!

  • Solvent-based paints can be recoated with ColorMatic 1 component clear coat once they have dried for 30 minutes
  • Shake can for 2 minutes
  • Carry out spray test
  • 1K Clear Coat glossy: For spot repairs, cover the wet edges of the clear coat ColorMatic Spot Blender no. 114229
  • Not suitable for recoating water-based paints (we recommend CM 2K Clear Coat high-gloss no. 187216, 190469)
  • Don't spray on synthetic resin areas!
  • For an optimal coating result bring can to temperature prior to use (20 - 25 °C) and a relative air humidity of 45 - 60%.
    Please note: a high air humidity can cause loss of gloss.
  • For professional use only
  • Use an adequate respirator mask (we recommend type A2/P3)
Technical Information 1K Clear Coat
2 min
Technical Information 1K Clear Coat
Technical Information 1K Clear Coat
5 min
Technical Information 1K Clear Coat
20°C=24 h
60°C=40 min
Technical Information 1K Clear Coat
15-20 min
Technical Information 1K Clear Coat
20°C=24 h
60°C=40 min
IR=15-20 min
Technical Information 1K Clear Coat
Technical Information 1K Clear Coat

Order information

 Color   Product   Bundle   Art.No. 
 CM 1K Klarlack hgl. 400   400 ml   756849 
 CM 1K Klarlack matt 400   400 ml   335600 
 CM 1K Klarlack sdgl.400   400 ml   369421 

* no color identification possible
The presentation of colors may deviate from the original color.
For printing of the order information please press "printing preview/further products".

Examples for use

Technical Information 1K Clear Coat
Technical Information 1K Clear Coat

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.

For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.

As of September 30, 2015
This release replaces all eventually earlier issued versions


From 4.-7. March the world's largest and most international exhibition – the International Hardware Fair 2018, Cologne – will show what is and will...

Read more


Porous material and holes up to 1 cm wide can easily be bridged or repaired in broken plastic using presto extra Fibreglass Filler.


Also suitable...

Read more

Even damage to metal or metal sheets can be easily repaired with presto alu Metal Filler. The finished repairs blend in well and are waterproof.


Read more