Technical information Multi-primer
Fast drying multi-primer spray for interior and exterior. Suited as all-purpose primer on iron, steel, zinc, aluminium, anodized aluminium, V2A steel, powder-coated components, different plastics and wood. Active corrosion protection and exceptional adhesion. Heat-resistant to 80°C dry heat and high filling capacity. Adjustable spray cone width (horizontally and vertically).
Application area: On job-sites at renovation. Ideal when fastness and mobility are the primary considerations. For certain preparation of the surface.
Quality and properties
- Universal Primer for steel, galvanized steel, GRP, wood, PVC, etc.
- Excellent preparation of the surface at versatile application possibilities
- Based on synthetic resins
- active corrosion protection
- Weather resistant
- quick drying
- very good adhesion
- heat resistant up to 80°C dry heat
- nitro thinner resistant (after through drying)
Physical and chemical data
- Basis of binder: Synthetic resins
- Colour: specific
- Smell: solvent
Depending on consistence and colour of the ground:
400 ml are sufficient for approx. 1,5-2 m²
Iron, steel, aluminium, zinc, anodized aluminium, V2A steel, powder-coated components, different plastics like rigid pvc, polyester, polyamide, ABS and wood
- Drying time (at 20°C, 50% relative air humidity):
Dust-dry: 40 min
Touch-dry: 60 min
Re-coatable: 3-4 h
The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
- Temperature resistance: to 80°C (dry heat)
- Storage stability:
10 years if appropriabte storage provided (=10°-25°C, relative air humidity of max. 60%)
Aerosol cans, maximum nominal volume 400 ml
- VOC-value: 740 g
Environment and labelling
Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.
Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse".
Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,
- Clean surfaces to be painted thoroughly with ColorMatic Degreaser Spray art.no. 447266, then sand
- The area must be dry and free of dust and grease
- Shake can well for 3 minutes
- Carry out spray test
- 2-3 coats
- Wear an appropriate respirator (type A2/P3)
|DC Allgrund 7001 grau 400||400 ml||478352|
|DC Allgrund 9010 weiß 400||400 ml||478369|
* no color identification possible
The presentation of colors may deviate from the original color.
For printing of the order information please press "printing preview/further products".
Disclaimer of liability
This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.
For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.
As of February 16, 2018
This release replaces all eventually earlier issued version.