Technical Information Putty for Plastic "styrene-free"
presto Putty for plastics "styrene-free" is a 2-component black polyester putty. To fill scratches and damages and to aftertreat bonded plastic parts.
Due to its thixotropy and softness, profiles and contours can easily be rebuilt. The putty adheres to all customary hard plastics, such as PP, ABS, PA, PVC.
Besides the very good adhesion on nearly all plastics, the putty can also be applied on carbody sheets and zinc coated sheets.
Quality and properties
- Ease of working
- High elasticity
- Easy to sand
- Very good adhesion
- Free of asbestos and silicone
- Resistant to weak acids and bases, propellants, solvents, water and de-icing salt
Physical and chemical data
- Basis: polyester resin with mineral fillers
- Colour: black
- Smell: characteristic
- Consistence: soft, thixotropic, pasty
- Pot life / Working time at 20°C: approx. 7 - 8 minutes
- Working temperature: min. 12°C
- Drying time (at 20°C, 50% relative air humidity):
can be sanded after approx. 30 - 40 minutes
- Flash point:
approx. 33°C (resin); not applicable for hardener
- Density at 20°C:
putty 1.89 g/cm³
hardener 1.15 g/cm³
- Addition of hardener: 2 - 4 % (optimal mixture 2,5 %)
- Temperature resistance of the cured material: 120°C
- Storage stability:
18 months if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) in the unopened original container. Protect from direct sunlight, frost and humidity.
small ring tins; hardener: plastic tubes
Environment and labelling
Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.
Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse".
Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,
Before use, carefully read and observe the warning texts on the label!
- The object you wish to repair should be de-rusted, clean, dry, fat-free and sanded.
- Take the requested portion of putty compound out of the can and mix it well with the corresponding quantity of hardener.
- Apply the mixed material in the desired layer thickness.
- Clean tools immediately after use, if necessary with a nitro thinner.
- Do not return mixed material into the can.
- After approx. 30-40 minutes the repaired spot can be drilled, sanded, sawed, rasped and painted.
- The putty adheres to all customary hard plastics in the car, such as PP, PUR, ABS, PA, PVC.
- Not suitable for weak plastics!
|presto SF Kunststoffsp. 250g||250 g||443381|
* no color identification possible
The presentation of colors may deviate from the original color.
For printing of the order information please press "printing preview/further products".
Examples for use
Disclaimer of liability
This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.
For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.
As of February 24, 2011
This release replaces all eventually earlier issued versions.