Technical Information Starting Spray
presto Starting Spray provides fast-action ether-based assistance for combustion engine ignition problems. The extremely ignitible composition allows a quick start. Simply spray in the engine suction filter.
For use on:
Combustion engines of all kinds e.g. car, bicycles, lorries, vans, chain saws, trimmers, tractors, diesel engines and gas engines
Quality and properties
- Easy application
- Ether, propane and butane mixture
- Fast acting
- Misty spray
- TRG 300 compliant
Physical and chemical data
- Basis: Diethylether and mineral oil
- Colour: transparent
- Smell: characteristic
- Relative density at 20°C: 0.711 g/ml
- Yield: 1.70 g/sec.
- Vapour pressure at 20°C: 3 - 4 bar
- Flash point: -40°C
- Explosion limit: Lowest 1.7 Vol%, Highest 36 Vol%
- Storage stability:
10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
aerosol can, maximum nominal volume 400 ml
Environment and labelling
Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.
Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse".
Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,
- Bring the can to room temperature.
- Shake can for 2 minutes before use.
- Spray presto Starting Spray for a few seconds in the air filter inlet.
- Then, start the engine immediately.
- For petrol engines – keep foot on the accelerator during ignition.
- For diesel engines – start the engine and leave running.
- In very cold conditions, continue to spray for a few seconds after ignition.
- Do not use with preheat spirals or candles or other preheat devices.
Tips for spray painting
Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.
The aerosol can should have room temperature.
Temperature should range between +10°C and +25°C, max. air humidity 60 %.
Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!
|Starthilfe-Spray 150ml||150 ml||429804|
|Starthilfe-Spray 400ml||400 ml||306413|
* no color identification possible
The presentation of colors may deviate from the original color.
For printing of the order information please press "printing preview/further products".
Examples for use
Disclaimer of liability
This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.
For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.
As of: April 4, 2011
This release replaces all eventually earlier issued versions.