Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Vermischung der A-Komponente mit dem Härter: Vor dem Aktivieren der A-Komponente die Dose unbedingt so lange schütteln, bis die innenliegenden Mischerkugeln deutlich hörbar sind. Schutzkappe am Dosenboden entfernen und den Stift mithilfe des eingelegten Ringes bis zum Anschlag herausziehen. Dadurch wird das Messer aufgestellt und das Messer durchstößt die Wand der Aluminiumkartusche. Durch anschließende 360° Drehung wird die Kartusche komplett geöffnet und der Härter freigesetzt. Durch kräftiges Schütteln der Dose (2 Minuten) wird nun die A-Komponente mit dem Härter im richtigen, vorgegebenen Mischungsverhältnis vermischt. Probesprühen Topfzeit: 48 Std. (20°C) Nur zur Benutzung durch den Fachmann Geeignete Atemschutzmaske tragen (wir empfehlen Typ A2/P3) Tipps zur Anwendung Vor Gebrauch die Dose auf Raumtemperatur (20 - 25°C) bringen. Dazu die Dose in handwarmes Wasser legen. 2 min 3=120µ 20°C=24 h 5 min Order information
Putty Dispenser Putty Dispenser This easy-to-mount putty wall dispenser is ideal for professionals. It takes 3000g tins of ColorMatic universal putty no. 702532 and always mixes the exact ratio of putty and hardener and provides the required amount of putty. This portable version is practical, economical and can be used anywhere, delivering accurate mixing ratios. Data sheet Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Examples for use
AB&C Glossy black, white and a clear lacquer: excellently suitable for all handicraft and DIY works on wood, metal, aluminium, glass, stone, carton, paper, eternite, porcelain and many coatable plastics. Data sheet Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Examples for use
Technical information 2K Hi-Speed Clear Coat satin glossy ColorMatic 2K clear coat is a extremely scratch-resistant 2-component clear coat. It is highly fuel-resistant, resistant to U.V.-rays and weather influences. Because of its very good flow and ease of polish, ColorMatic 2K clear coat is particularly suitable for spot repairs. Use ColorMatic spot blender for spot repairs. Ready-filled ColorMatic pre-fill products can be recoated once they have dried for 30 minutes. Old paintwork has to be fully dry. Application: Ideal for spot repairs and refinishing parts Hier erhalten Sie die Erklärung der 2K-Technologie im Film Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Quality and properties Special effect coating for tuning parts Spot coating for plastic parts Coating for plastic parts A high-gloss, extremely scratch-resistant 2-component clear coat – highly fuel-resistant, resistant to U.V. rays and weather influences. Provides gloss effect with 50 ° / 60 ° in OEM quality Long pot life Fast drying time Very good flow Convenient 200 ml can to avoid leftover Physical and chemical data Basis of binder: Acrylic Colour: transparent Smell: solvent Degree of gloss: (at measurement angle 60° acc. to DIN 67530) satin gloss: ca. 30 gloss units Efficiency: epending on consistence and colour of the ground: 200 ml are sufficient for approx. 0,3 - 0,4 m² Substrate: solvent- and water-based base coats Drying time (at 20°C, 50% relative air humidity): Dust-dry: after approx. 5 minutes Dry to touch: after approx. 5 hours The drying time depends on surrounding temperature, air humidity and thickness of the applied coat. Temperature resistance: to 120°C Storage stability: 36 month if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) Size: 2 components aerosol cans, maximum nominal volume 200 ml VOC-value: 123,5g Pot-life: 24 hours at room temperature (20 - 25°C) 5 days at cool storage (6°C) Befor using again warm up to room temperature (20 - 25°C). See using instruction. Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Base coatings can be coated ColorMatic 2K hi-speed clear coat silk once they have dried for 30 minutes 2-3 full coats, 50µ Leave to dry for 2 minutes between coats For an optimal coating result bring can to temperature prior to use (20 - 25 °C) and a relative air humidity of 45 - 60%. Please note: a high air humidity can cause loss of gloss. Mixing A components with hardener: Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 2 minutes Carry out spray tests Pot life: 24 hours (20 ° C) Ready-to-use coating materials containing isocyanates can irritate the respiratory system and cause allergic reactions. There is a risk of sensitization with inhalation of vapours and spray mist. When dealing with substances containing isocyanates, you should observe all guidelines for using solvent-based coatings. In particular, spray mist and vapours should not be inhaled. Allergy and asthma sufferers and people who are prone to respiratory diseases should not work with isocyanates materials.• For professional use only• Wear an appropriate respirator (recommended type A2/P3) 2 min 2-3=50µ 2 min 20°C=7 h 60°C=45 min 25 min 20°C=7 h 60°C=45 min IR=30 min Order information Oops, an error occurred! Code: 20190321182335b70fa5d9 Examples for use Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m. As of September 30, 2015 This release replaces all eventually earlier issued versions.
Technical information 2K Hi-Speed Clear Coat matt For high quality matt surfaces. ColorMatic 2K Clear Coat matt offers an extremely scratch-resistance with very high resistance to petrol, UV rays and weathering. Dries quick and has a very good flow. Application: Ideal for the painting of parts with matt visual appearance. Click here for a demonstration of the 2 K technology in a video. Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Quality and properties Special effect coating for tuning parts Wheels in high class matt finish Coating for plastic parts A high-gloss, extremely scratch-resistant 2-component clear coat – highly fuel-resistant, resistant to U.V. rays and weather influences. Long pot life Fast drying time Very good flow Convenient 200 ml can to avoid leftover Physical and chemical data Basis of binder: Acrylic Colour: transparent Smell: solvent Degree of gloss: (at measurement angle 60° acc. to DIN 67530) matt at 2 spraying passes: 20 +/- 10 gloss units (depending on the substrate and numbers of spraying passes) Efficiency: depending on consistence and colour of the ground: 200 ml are sufficient for approx. 0,3 - 0,4 m² Substrate: solvent- and water-based base coats Drying time (at 20°C, 50% relative air humidity): Dust-dry: after approx. 5 minutes Dry to touch: after approx. 5 hours The drying time depends on surrounding temperature, air humidity and thickness of the applied coat. Temperature resistance: to 120°C Storage stability: 36 month if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) Size: 2 components aerosol cans, maximum nominal volume 200 ml VOC-value: 94 g Pot-life: 24 hours at room temperature (20 - 25°C) 5 days at cool storage (6°C) Befor using again warm up to room temperature (20 - 25°C). See using instruction. Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Base coatings can be coated with ColorMatic 2K hi-speed clear coat matt once they have dried for 30 minutes (if surface is dust-dry) 2-3 full coats, 45µ Leave to dry for 3 minutes between coats For an optimal coating result bring can to temperature prior to use (20 - 25 °C) and a relative air humidity of 45 - 60%. Please note: a high air humidity can cause loss of gloss. Mixing A components with hardener: Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 3 minutes Carry out spray tests Pot life: 24 hours (20 ° C) Ready-to-use coating materials containing isocyanates can irritate the respiratory system and cause allergic reactions. There is a risk of sensitization with inhalation of vapours and spray mist. When dealing with substances containing isocyanates, you should observe all guidelines for using solvent-based coatings. In particular, spray mist and vapours should not be inhaled. Allergy and asthma sufferers and people who are prone to respiratory diseases should not work with isocyanates materials.• For professional use only• Wear an appropriate respirator (recommended type A2/P3) 3 min 2-3=30-45µ 3 min 20°C=90 min 60°C=25 min 15 min Order information Oops, an error occurred! Code: 201903211821178d4bd875 Examples for use Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m. As of September 30, 2015 This release replaces all eventually earlier issued versions.
Technical information 2K Epoxy Primer Filler ColorMatic 2K epoxy primer filler is universally applicable to all metallic surfaces such as steel, galvanized steel and aluminium. It has excellent adhesion and corrosion protection properties and adheres well to fibreglass plastics. Once dry, overcoat with polyester products (spatula). It is solvent-based with an epoxy-resin basis. Free of isocyanate. Applications: Ideal for spot repairs and refinishing parts Click here for a demonstration of the 2 K technology in a video. Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Quality and properties Excellent adhesion and corrosion protection for steel, galvanized steel and aluminium Adheres well to fibreglass Once dry, overcoat with polyester products (spatula) Long pot life Fast drying time Very good flow, wet-on-wet application possible Easy to sand - wet or dry Solvent resistant Good insulation against moisture Convenient 200 ml can to avoid leftover Simple, time-saving application Free of isocyanate Can be painted with all ColorMatic pre-fill water-based paints and solvents, 1K and 2K topcoats Physical and chemical data Basis of binder: EP Colour: beige Smell: solvent Efficiency: Depending on consistence and colour of the ground: 200 ml are sufficient for approx. 0,6 m² Substrate: bare metal cleaned and sanded, zinc coated metal cleaned and sanded, Aluminium cleaned and sanded, old paints cleaned and sanded, glass-fibre plastic cleanded and sanded Temperature resistance: to 90°C Storage stability: 24 month if appropriate storage is provided (=10°-25°C, relative air humidity of max. 60%) Size: Aerosol cans, maximum nominal volume 200 ml VOC-value: 108,6g Pot life: 5 days at least (20°C) Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Clean surface with ColorMatic silicone remover no. 174469, then sand Primer: one coat about 15 - 20µ Filler: two coats, about 50-60µ 5 minutes drying time between coats Dry (20 ° C) 8 hours or 25 minutes (60 ° C) object temperature Wet-on-wet recoating possible after 20 minutes drying time The surface has to be sanded and recoated after 7 days Mixing A components with hardener: Shake can well until the audible noise of the mixing balls Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 2 minutes Carry out spray test For professional use only Wear an appropriate respirator (we recommended type A2/P3) Hints concerning application When stored at cool temperatures, the 2K Hi-Speed epoxy primer filler may also be used for several days following activation. Prior to use, heat to room temperature (approx. 20°). 2 min 2=60 µ 20°C=8h 20 min P800-1000 P400-500 variable order information Oops, an error occurred! Code: 20190321182039e9bb2d44 Examples for use Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m. As of June 23, 2017 This release replaces all eventually earlier issued versions.
Technical information 1K Filler ColorMatic 1K filler is an advanced 1K acrylic filler with excellent filling properties and coverage. It is highly suitable for levelling superficial scratches and minor irregularities in sanded surfaces. It offers excellent adhesion on polyester filler, plastics and metal. It has a very good flow, is wet-on-wet re-sprayable and easy to sand. Application: Ideal for spot repair and refinishing of parts. Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Quality and properties Advanced 1K acrylic filler with excellent filling properties and coverage Wet-on-wet application possible Very good for filling minor scratches and uneven areas on sanded undercoats Good adhesion to all metal surfaces Very smooth flow Physical and chemical data Basis of binder: Acrylic resin Colour: beige (856556), grey (874987) Smell: Solvent Efficiency: 400ml are sufficient for approx. 1,25 - 1,75 m² Substrate: blank metall, sanded, priming of spare parts, sanded, cured paintings, sanded, polyester substrates, sanded, steel, sanded and aluminium, sanded Temperature resistance: to110°C Storage stability: 10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) Size: Aerosol cans, maximum nominal volume 400 ml VOC-value: 217g Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Remove all rust from damaged areas, where appropriate Clean surface thoroughly and sand Damaged area must be dry and free of grease and dust Shake the can well for 2 minutes Carry our spray test Clean undercoat with ColorMatic Silicone Remover, art. no. 174 469 Large bare areas should be pre-treated with the appropriate ColorMatic primers Do not overcoat with polyester products For professional use only Use an adequate respirator mask (we recommend type A2/P3) 2 min 3=30-60µ 5 min 8-10 min 20°C=60 min P800-1000 P400-500 variable Order information: Oops, an error occurred! Code: 20190321182151cd7a9184 Examples for use Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m. As of August 25, 2017 This release replaces all eventually earlier issued versions.
Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Base coatings can be top-coated with ColorMatic 2K hi-speed clear coat after drying for 30 minutes 2-3 full coats, 50µ Leave to dry for 2 minutes between coats Mixing A components with hardener: Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 2 minutes Carry out spray tests Pot life: 24 hours (20 ° C) Ready-to-use coating materials containing isocyanates can irritate the respiratory system and cause allergic reactions. There is a risk of sensitization with inhalation of vapours and spray mist. When dealing with substances containing isocyanates, you should observe all guidelines for using solvent-based coatings. In particular, spray mist and vapours should not be inhaled. Allergy and asthma sufferers and people who are prone to respiratory diseases should not work with isocyanates materials. For professional use only Wear an appropriate respirator (recommended type A2/P3) 3 min 2-3=30-50µ 2 min 20°C=90 min 60°C=25 min Hints concerning application For an optimal coating result bring can to temperature prior to use (20 - 25 °C) and a relative air humidity of 45 - 60%. Please note: a high air humidity can cause loss of gloss. Order information
Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Base coatings can be recoated with ColorMatic 2K hi-speed clear coat after drying for 30 minutes 2-3 full coats, 50µ Leave to dry for 2 minutes between coats Mixing A components with hardener: Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 2 minutes Carry out spray tests Pot life: 24 hours (20 ° C) Ready-to-use coating materials containing isocyanates can irritate the respiratory system and cause allergic reactions. There is a risk of sensitization with inhalation of vapours and spray mist. When dealing with substances containing isocyanates, you should observe all guidelines for using solvent-based coatings. In particular, spray mist and vapours should not be inhaled. Allergy and asthma sufferers and people who are prone to respiratory diseases should not work with isocyanates materials. For professional use only Wear an appropriate respirator (recommended type A2/P3) Hints concerning application For an optimal coating result bring can to temperature prior to use (20 - 25 °C) and a relative air humidity of 45 - 60%. Please note: a high air humidity can cause loss of gloss. 3 min 2-3=50 µ 2 min 20°C=7 h Order information
Technical information 2K Hi-Speed Primer Filler ColorMatic 2K hi-speed primer is universally applicable to all metallic surfaces such as steel, galvanized steel and aluminium. It offers excellent adhesion and corrosion protection and is very fast drying: 1 h (20 ° C). It is perfect for sanding, wet and dry. It is also solvent resistant. Applications: Ideal for spot repairs and refinishing parts. Click here for a demonstration of the 2 K technology in a video. Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Quality and properties Filler and primer at the same time Long pot life Very fast drying time Very good flow Universal applicable for polished old paintwork and metal surfaces Best to use 200 ml can to avoid surplus Simple, time-saving application Good adhesion to bare steel, galvanized steel and aluminium Recoat with ColorMatic pre-fill based paints, acrylic RAL Physical and chemical data Basis of binder: Acrylic Colour: grey Smell: solvent Efficiency: Depending on consistance and colour of the ground: 400 ml are sufficient for 1,5 m² Substrate: bare metal cleaned and sanded, zinc-coated metal cleaned and sanded, Aluminium cleaned and sanded, PE-Putty cleaned and sanded, plastic substrates should be pre-treated with ColorMatic 1K Plastic Adhesive Temperature resistance: to 80°C Storage stability: 36 month if appropriate storage is provided (=10°-25°C, relative air humidity of max. 60%) Size: 2 components aerosol cans, maximum nominal volume 500 ml and 200 ml VOC-value: 114,2g Pot life: 24 h at least Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Clean surface with ColorMatic silicone remover no. 174469, then sand Old paintwork has to be cleaned and sanded 2-3 coats, 40 to 50µ Leave to dry for approximately three minutes between coats Ready to sand after about 45 min (20 ° C) or 30 min (60 ° C) Ready to recoat wet-on-wet after 20 minute drying time Mixing A components with hardener: Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 2 minutes Carry out spray test For professional use only Wear an appropriate respirator (recommended type A2/P3) Hints concerning application For smoothing over small unevenness, you can apply the ColorMatic 2K Hi-Speed primer filler up to a layer thickness of approx. 100 µ. For best full drying results, we recommend working with several thin spray applications and a flash off time between the spray passes of approx. 3 minutes. When stored at cool temperatures, the 2K Hi-Speed primer filler may also be used for several days following activation. Allow to heat to room temperature prior to use (approx. (approx. 20°). 2 min 2-3=60-80µ 20°C=2 h 15-20 min P800-1000 P400-500 variable Order information Oops, an error occurred! Code: 2019032118254661ed44b6 Examples for use Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m. As of March 21, 2012 This release replaces all eventually earlier issued versions.