Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Base coatings can be recoated with ColorMatic 2K hi-speed clear coat after drying for 30 minutes 2-3 full coats, 50µ Leave to dry for 2 minutes between coats Mixing A components with hardener: Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 2 minutes Carry out spray tests Pot life: 24 hours (20 ° C) Ready-to-use coating materials containing isocyanates can irritate the respiratory system and cause allergic reactions. There is a risk of sensitization with inhalation of vapours and spray mist. When dealing with substances containing isocyanates, you should observe all guidelines for using solvent-based coatings. In particular, spray mist and vapours should not be inhaled. Allergy and asthma sufferers and people who are prone to respiratory diseases should not work with isocyanates materials. For professional use only Wear an appropriate respirator (recommended type A2/P3) Hints concerning application For an optimal coating result bring can to temperature prior to use (20 - 25 °C) and a relative air humidity of 45 - 60%. Please note: a high air humidity can cause loss of gloss. 3 min 2-3=50 µ 2 min 20°C=7 h Order information
Technical information 2K Hi-Speed Primer Filler ColorMatic 2K hi-speed primer is universally applicable to all metallic surfaces such as steel, galvanized steel and aluminium. It offers excellent adhesion and corrosion protection and is very fast drying: 1 h (20 ° C). It is perfect for sanding, wet and dry. It is also solvent resistant. Applications: Ideal for spot repairs and refinishing parts. Click here for a demonstration of the 2 K technology in a video. Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Quality and properties Filler and primer at the same time Long pot life Very fast drying time Very good flow Universal applicable for polished old paintwork and metal surfaces Best to use 200 ml can to avoid surplus Simple, time-saving application Good adhesion to bare steel, galvanized steel and aluminium Recoat with ColorMatic pre-fill based paints, acrylic RAL Physical and chemical data Basis of binder: Acrylic Colour: grey Smell: solvent Efficiency: Depending on consistance and colour of the ground: 400 ml are sufficient for 1,5 m² Substrate: bare metal cleaned and sanded, zinc-coated metal cleaned and sanded, Aluminium cleaned and sanded, PE-Putty cleaned and sanded, plastic substrates should be pre-treated with ColorMatic 1K Plastic Adhesive Temperature resistance: to 80°C Storage stability: 36 month if appropriate storage is provided (=10°-25°C, relative air humidity of max. 60%) Size: 2 components aerosol cans, maximum nominal volume 500 ml and 200 ml VOC-value: 114,2g Pot life: 24 h at least Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Clean surface with ColorMatic silicone remover no. 174469, then sand Old paintwork has to be cleaned and sanded 2-3 coats, 40 to 50µ Leave to dry for approximately three minutes between coats Ready to sand after about 45 min (20 ° C) or 30 min (60 ° C) Ready to recoat wet-on-wet after 20 minute drying time Mixing A components with hardener: Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 2 minutes Carry out spray test For professional use only Wear an appropriate respirator (recommended type A2/P3) Hints concerning application For smoothing over small unevenness, you can apply the ColorMatic 2K Hi-Speed primer filler up to a layer thickness of approx. 100 µ. For best full drying results, we recommend working with several thin spray applications and a flash off time between the spray passes of approx. 3 minutes. When stored at cool temperatures, the 2K Hi-Speed primer filler may also be used for several days following activation. Allow to heat to room temperature prior to use (approx. (approx. 20°). 2 min 2-3=60-80µ 20°C=2 h 15-20 min P800-1000 P400-500 variable Order information Oops, an error occurred! Code: 2019032118254661ed44b6 Examples for use Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m. As of March 21, 2012 This release replaces all eventually earlier issued versions.
Techical Information Vaseline Spray presto Vaseline Spray is a reliable lubrication that also protects metals such as aluminium, copper, brass, chrome, steel etc. from acids, lyres and salt. For use on: Antennae, plug-in connections and bolted connections and locks Available colours/order numbers Search dealer for this product Stepwise Manual General Remarks Quality and properties Prevents wear and clamping of treated parts Medicinal qualities Non-poisonous on contact with food Water repellent Non-conducting Excellent lubrication Excellent mechanical stability Resistant to the effects of weather Saltwater, weak acid and lyre proof Excellent adhesion Good corrosion protection Acid free Misty spray TRG 300 compliant Physical and chemical data Basis: Vaseline Colour : white Smell: characteristic Relative density at 20°C : 0.89 g/ml Yield : 1.11 g/sec. Vapour pressure at 20°C : 3 - 4 bar 4 Ball EP-test (AS TM D 2596): 3136 N 4 Ball Wear-test (AS TM D 2266): < 0,4 mm Drop point: 42°C to 60°C Temperature resistance: -30°C to +160°C pH-value: neutral Storage stability: 10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) Size: aerosol can, maximum nominal volume 400 ml Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Application: Bring spray to room temperature. Operating temperature 5° to 30°C. Shake can for 2 minute before use. Spray onto the parts to be treated. Optimum lubrication occurs once the solvent has evaporated. Tips for spray painting Protect the object and the surrounding area from spray mist. Temperature should range between +10°C and +25°C, max. air humidity 60 %. Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels! Order informations Oops, an error occurred! Code: 20190321182430db636428 Examples for use Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m. As of October 14, 2011 This release replaces all eventually earlier issued versions.
Technical data Sheet spot remover Distein spot remover is specially formulated to clean up stains on clothes left behind by DISTEIN forest marking paints. Spray the stained area liberally with the spot remover and blot away carefully, do not rub. Repeat as necessary. Suitable for colored spots from Distein marking paint. Available colours/order numbers Stepwise Manual General Remarks Quality and properties mild effect universal usable good separation force no residues not corrosive Physical and chemical data Color: transparent smell: characteristic basic: specific solvent Storage stability: 10 years if appropriate storage provided (10°-25°C, relative air humidity of max. 60%) Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using Instructions Before use, carefully read and observe the warning texts on the label! Before use, shake can well for 2 minutes. Spray to test colour and compatibility on an inconspicious area. Distance approx 10-15 cm Order information Oops, an error occurred! Code: 2019032118240586970c22 Disclaimer of liability This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI. For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m. As of October 29, 2012 This release replaces all eventually earlier issued versions.
Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions Before use, carefully read and observe the warning texts on the label! Clean surface with ColorMatic silicone remover no. 174469, then sand Primer: one coat about 15 - 20µ Filler: two coats, about 50-60µ approx. 5 minutes drying time between coats Dry (20 ° C) 8 hours or 25 minutes (60 ° C) object temperature Wet-on-wet recoating possible after 20 minutes drying time The surface has to be sanded and recoated after 7 days Mixing A components with hardener: Shake can well until the audible noise of the mixing ball Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge. The cartridge will then rotate 360 °, be completely open and release the hardener. Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio. Shake can vigorously for 2 minutes Carry out spray test For professional use only Wear an appropriate respirator (we recommended type A2/P3) Hints concerning application When stored at cool temperatures, the 2K Hi-Speed epoxy primer filler may also be used for several days following activation. Prior to use, heat to room temperature (approx. 20°). 2 min 20°C=8 h P400-500 variable order information
Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions The most DUPLI-COLOR spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label. Before use, carefully read and observe the warning texts on the label! Application: Before use, shake can for 3 minutes. Condition for a perfect paint repair is a careful preparation of the ground: spots of rust have to be pre-treated with Rust Converter, other bigger dents have to be sanded down to the blank metal and to be filled. After drying sand even with wet-sandpaper grain 240. In case of small dents, scratches or similar paint damages, the product is a primer and a filler in one product. Just slightly sand the damaged area with wet-sandpaper and then overspray it with DUPLI-COLOR Filler. If necessary, apply a second coat after 30 minutes. After drying (approx. 2 hours), sand with wet-sandpaper grain 600 and plenty of water in a circular motion. Also slightly sand the bordering paint surface, in order to achieve a smooth transition. After sanding, remove abrasive dust by washing and let surface dry. Then apply the final coat of DUPLI-COLOR Auto-Spray. Coatable with synthetic or acrylic lacquers; do not spray over synthethic paints. Tips for spray painting Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist. The aerosol can should have room temperature. Temperature should range between +10°C and +25°C, max. air humidity 60 %. Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels! Order information
Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions The most DUPLI-COLOR spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label. Before use, carefully read and observe the warning texts on the label! Preparation of the ground: De-rust, sand and clean the surfaces to be painted. Apply putty, if necessary. The surface has to be clean, dry and free from rust and fat. Applying the primer: Shake cans for 2 minutes. Egalize little dents and porous repair spots by repeated spraying of thin layers and sanding. Spray from a distance of approx. 25 cm. After drying (approx. 2-4 hours), wet-sand with sandpaper (grain 600), clean the surface and let it dry. Afterwards apply the top coat. Coatable with synthetic or acrylic lacquers. Do not spray over synthetic lacquers! Tips for spray painting Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist. The aerosol can should have room temperature. Temperature should range between +10°C and +25°C, max. air humidity 60 %. Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels! Order information
Environment and labelling Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material. Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as "special refuse". Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II, Using instructions The most DUPLI-COLOR spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label. Before use, carefully read and observe the warning texts on the label! Preparation of the ground: Dry-sand with fine sandpaper (grain 600), carefully remove abrasive dust. The surface has to be clean, dry and free of fat. Priming: Shake can for 2 minutes. Test spray at an invisible spot. Spray 2 - 3 thin layers. Spray from a distance of approx. 25 cm. After drying (approx. 2 - 4 hours), apply the top coat. Coatable with air-drying acrylic or synthetic lacquers. Tips for spray painting Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist. The aerosol can should have room temperature. Temperature should range between +10°C and +25°C, max. air humidity 60 %. Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels! Order information
