Scheda tecnica Alkyton heat-resistant brush paint
Proprietà chimico-fisiche
- Basis of the Binder: Silicone-modified alkyd resin
- Colour: black matt and silver
- Smell: solvent
- Efficiency:
Theoretical: 10 - 12 m²/l. Can vary depending on colour and condition of the ground
Practical: Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application (see DIN 53220) - Recommended layer thickness: 35-40 µm dry, corresponds to approx. 85 µm wet
- Drying (at 20°C, 50% relative air humidity):
Tack-free: after 2 hours
Dry to touch: after 8 hours
Re-coatable after 24 hours
Full hardness: 24 hours after the minimum service temperature of 150°C is reached. Gradually heat the coating to 150°C (max. 50°C/hour. - Densitiy: black: 1,38 g/cm³, silver: 1,11 g(cm³
- Solids Content: black: 40 %, silver: 47 % by volume ± 2,0 depending on colour
- Viskosity:
880 - 1150 mPA s (880 - 1150 cP) - Flash Point: 40°C
- Temperature resistance:
up to 600°C (dry heat), short term peak load up to 750°C - VOC-content: 460 g/ l max.
Category: IIA/ i
EU Limit values: 600 g/ l (2007)/ 500 g/ l (2010) - Storage stability:
5 years from date of production in unopen can, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C. - Disposal: Put only empty can into the recycling bin. Bring cans with remainders of paint to the special refuse disposal.
- Content: max. nominal volume = 250 ml or 750 ml
Ambiente ed etichettatura
Rispetta l’ambiente: European Aerosols si impegna ad applicare le formulazioni dei prodotti senza sostanze vietate o in restrizione e ad ottenere le migliori prestazioni possibili. I cappucci e gli imballi sono costituiti di materiale riciclabile.
Smaltimento: controllare che nel contenitore non rimangano residui di vernice. Smaltire il contenitore vuoto negli appositi contenitori per il riciclaggio. I contenitori con residui di vernice devono essere smaltiti nei punti di raccolta rifiuti pericolosi o speciali.
Etichettatura: tutti i prodotti European Aerosols sono rispondenti alle attuali normative in materia di classificazione ed etichettatura. La classificazione e la distinzione avvengono in accordo con la legislazione del sistema Globale armonizzato di classificazione ed etichettatura delle sostanze chimiche (GHS) o ai sensi del Regolamento CLP 1272/2008 CE. Le nostre schede di sicurezza sono conformi alla versione attuale REACH 1907/2006 CE, articolo 31, appendice II.
Surface preparation:
Remove grease, oil, dirt, loose rust, loose coatings and any other contamination with suitable agents. Sand intact, old paintwork to obtain a good adhesion. The surface must be clean and dry during application.
Mixing and thinning:
The paint has to be stirred vigorously before use. Do not thin!
Application:
Apply only if the air and surface temperatures are between 5 and 35°C and the relative humidity is less than 85%. Apply with a brush. Due to the high viscosity we do not recommend application in a spray gun.
Coatable: after 24 hours. Fully cured: 24 hours after the minimum service temperature of 150°C is reached. Gradually heat the coating to 150°C (max. 50°C/hour).
Clean up of the tools: With white spirit.
Esonero di responsabilità
Queste informazioni tecniche si basano su conoscenze scientifiche. Sono da considerarsi tuttavia come indicazione non vincolante e non liberano il consumatore dall'effettuare personalmente i controlli sui prodotti circa la compatibilità con gli impieghi da lui previsti. L'applicazione e la lavorazione avvengono al di fuori del diretto controllo del produttore e sono di esclusiva responsabilità dell'utilizzatore. European Aerosols è sollevata da ogni responsabilità se l'eventuale danno non è riconducibile a cause specifiche imputabili alla stessa European Aerosols.
Ultimo aggiornamento: July 5, 2012
La presente versione annulla e sostituisce tutte le eventuali versioni precedenti.