Technical Information 1K Clear Coat

Technical Information 1K Clear Coat

ColorMatic 1K clear coat is a UV-resistant, fast-drying clear coat that can be applied universally at all existing base coats (solvent-based). Available in glossy, satin gloss and mat quality. Because of its very good flow and ease of polish, 1K Clear Coat glossy is highly suitable for spot repairs with solvent-based paints (e.g. ColorMatic solvent-based).

For best preparation of the surface which is to varnish, clean it thoroughly with ColorMatic Silicone Remover no. 174469 and, if required, apply a primer or filler  (e.g. ColorMatic 2K Primer Filler no. 195327). We recommend using ColorMatic Spot Blender no. 114229 for spot repair on the edges.

Application:
glossy: ideal for spot repairs and refinishing parts.
satin gloss and mat: painting of construction parts with mat look.

Quality and properties

  • Fast drying time
  • Easy application
  • Can be used on all solvent-based paints
  • UV resistant

    Especially at 1K Clear Coat glossy:
  • Highly suited for spot repairs due to good flow and being easy to polish
  • Light blending
  • High gloss

    Especially at 1K Clear Coat satin gloss and mat:
  • Ideal for all construction parts with a brilliant mat respectively satin gloss look
  • Tip: we advice at Clear Coat mat to paint the construction parts complete
  • Caution: don't polish!

Physical and chemical data

  • Basis of binder: Acrylic resin
  • Colour: transparent
  • Smell: solvent
  • Degree of gloss: at measurement angle 60° acc. DIN 67530
    glossy: 85 - 90 GE
    satin gloss: 60 GE
    mat: 10 (+/-5) GE
  • Efficiency:
    Depending of consistence and colour of the substrate 400 ml are sufficient for approx. 1,5 - 2,0 m²   
  • Substrate:
    Basecoats uni or metallic
  • Drying (at 20°C, 50% relative air humidity):
    Dust-dry: after 5 - 10 minutes
    Touch-dry: after 10 - 20 minutes
    Cured after 24 hours
    The drying time is depending on the ambient temperature, air humidity and the applied paint layer
  • Temperature resistance:
    glossy to 110°C
    mat to 80°C
  • Storage stability:
    10 years if appropriate storage provided (=10°-25°C, relative Luftfeuchte von max. 60%)
  • Size:
    Aerosol cans, maximum nominal volume 400 ml
  • VOC-Value:
    glossy 276,4 g
    satin gloss 271 g
    mat 253,9 g

 

Environment and labelling

Environmentally sound: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  MOTIP DUPLI comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Using instructions

Before use, carefully read and observe the warning texts on the label!

  • Solvent-based paints can be recoated with ColorMatic 1 component clear coat once they have dried for 30 minutes
  • Shake can for 2 minutes
  • Carry out spray test
  • 1K Clear Coat glossy: For spot repairs, cover the wet edges of the clear coat ColorMatic Spot Blender no. 114229
  • Not suitable for recoating water-based paints (we recommend CM 2K Clear Coat high-gloss no. 187216, 190469)
  • Don't spray on synthetic resin areas!
  • For an optimal coating result bring can to temperature prior to use (20 - 25 °C) and a relative air humidity of 45 - 60%.
    Please note: a high air humidity can cause loss of gloss.
  • For professional use only
  • Use an adequate respirator mask (we recommend type A2/P3)
Technical Information 1K Clear Coat
2 min
Technical Information 1K Clear Coat
2-3=40µ
Technical Information 1K Clear Coat
5 min
Technical Information 1K Clear Coat
20°C=24 h
60°C=40 min
Technical Information 1K Clear Coat
15-20 min
Technical Information 1K Clear Coat
20°C=24 h
60°C=40 min
IR=15-20 min
Technical Information 1K Clear Coat
Technical Information 1K Clear Coat
 
 
 
 
 

Order information

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

Products: The subpart part marker ###ITEM_LIST_EMPTY### or the template file EXT:snet_tmpl_motip/Resources/Private/Templates/Extensions/tt_products/products_template_en.tmpl has not been found.

Examples for use

Technical Information 1K Clear Coat
Technical Information 1K Clear Coat

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.

For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.

As of August 6, 2019
This release replaces all eventually earlier issued versions

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

Lelijke deuken op vleugels of bumpers kunnen snel en gemakkelijk verwijderd worden met MoTip laksprays.

Meer lezen

Hier kunt u gestileerde muurschilderingen in blad-patroon maken. De truc: de bladen worden niet geschilderd maar erop gespoten met stencil...

Meer lezen