Technical information 1K Etch Primer

Technical information 1K Etch Primer

ColorMatic 1K anti-corrosion primer has excellent adhesive properties, especially on polished metal, e.g. steel plate. Active rust protection pigments ensure optimum corrosion protection. Quick drying. Can also be used as a welding primer.

For best possible preparation of metal substrates, use Silicone Remover art.no. 174469 for thorough precleaning.

Application areas:Ideal for spot and part painting

Quality and properties

  • 1K acid primer, welder primer
  • Can be used for spot repairs and refinishing parts
  • Simple, time-saving application
  • Fast drying time
  • Excellent corrosion protection
  • Very good adhesion, especially on bare sanded metal

Physical and chemical data

  • Basis of binder: NC
  • Colour: red brown
  • Smell: solvent
  • Efficiency:
    1 m²
  • Substrate:
    sanded: blank metall, cured paintings, primer for refinishing parts, aluminium
  • Temperature resistance: to 90 °C
  • Storage stability:
    10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
  • Size:
    Aerosol cans, maximum nominal volume 400 ml
  • VOC value: 270,5g

Environment and labelling

Environmentally sound: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  MOTIP DUPLI comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Using instructions

Before use, carefully read and observe the warning texts on the label!

Instruction

  • 1-2 coats, when used as a primer
  • After airing for 10-50 minutes (20 ° C) with one of the following products can be continued on demand: ColorMatic 1K Fillers, 1K Primer Fillers HG2-HG6, HG8 (not HG1 and HG7!), 2K Hi-Speed Primer
  • One light coat when used as a welding primer
  • Remove all rust damaged area, clean surface thoroughly and sand. 
  • Area must be dry and free of grease and dust
  • Clean undercoat with ColorMatic Silicone Remover no. 174 469
  • Shake the can well for 2 minutes
  • Carry out test spray

  • For professional use only
  • Wear an appropriate respirator (recommended type A2/P3)
Technical information 1K Etch Primer
2 min
Technical information 1K Etch Primer
Primer 1-2
= 10-20 µ
Technical information 1K Etch Primer
to top-coat
20°C=10-15 min
Technical information 1K Etch Primer
3 min
Technical information 1K Etch Primer
Technical information 1K Etch Primer
approx. 15 cm
Technical information 1K Etch Primer
20°C=10-15 min
 
 
 
 
 

Hints concerning application

Bare sheet metal pretreated with ColorMatic 1K anti-corrosion primer can thus be protected against rust attack. This is of interest especially for workshops using repair sheet metal.

 

Order information

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

Products: The subpart part marker ###ITEM_LIST_EMPTY### or the template file EXT:snet_tmpl_motip/Resources/Private/Templates/Extensions/tt_products/products_template_en.tmpl has not been found.

Examples for use

Technical information 1K Etch Primer
Technical information 1K Etch Primer

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.

For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.

As of April 19, 2016
This release replaces all eventually earlier issued versions.

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

Kapotte randen kunnen snel weer aan elkaar gelijmd worden met de presto Bodyfiller, voor een langdurige stabiliteit.

 

Ook geschikt voor gebruik op:...

Meer lezen

Roestvlekken en gaten in de carrosserie van je wagen verminderen de verkoopwaarde ervan. Herstel zelf de schade in slechts enkele gemakkelijke...

Meer lezen