Technical manual 2K pre-fill HS Topcoat

Technical manual 2K pre-fill HS Topcoat

The ColorMatic pre-fill spray paint is prefilled with propellant and specific additives and then filled by VitoMat filling machines with the desired coat. Innovative spray and valve technology guarantee the fine broad jet atomisation, a high application rate and constant pressure for best workmanship and professional-quality end results.2K hs topcoat pre-fill offers the highest quality in terms of gloss, drying, and weather and petrol resistance.

 

 

Quality and properties

  • A spray can prepared with proellant gas, solvents and hardener (isocyanate containing) in a separate pre-filled cartridge. The 2K HS Topcoat is inserted in the can by a filling device and thus ready for the finished product
  • The mixing of the 2K topcoat with the hardener achieves an optimal quality with respect to gloss, curing, weather and chemical resistance
  • Simple, time-saving application
  • Excellent atomisation
  • Light blending


Ideal for spot repairs

Physical and chemical data

  • Basis of binder: Acryl
  • Colour: depending on filling
  • Smell: solvent
  • Efficiency:
    Depending on consistence and colour of the ground:
    400 ml are sufficient for approx. 0,8 m²
  • Substrate:
    according to colour of the ground 1K Primer Filler HG1 - HG8, ColorMatic 2K Hi-Speed Primer Filler no. 195 327, ColorMatic 1K Primer for ALU no. 190 278, ColorMatic 1K Primer for Zinc no. 190 285, ColorMatic 1K Epoxy Primer no. 174 414, ColorMatic 1K Filler, beige no. 856 556, ColorMatic 1K Filler, grey no. 874 987, cured paints sanded
  • Drying time (at 20°C, 50% relative air humidity):
    The drying time depends on surrounding temperature, air humidity and thickness of the applied coat and filled type of paint (refer to information of the paint manufacturer)
  • Storage stability: empty cans 36 month
    Pot life filled cans approx. 12 h (=10°-25°C, relative air humidity of max. 60%)
  • Size:
    Aerosol cans, maximum nominal volume 400 ml, filling amount 100ml for TC-1 230677, TC-2 249457, TC-4 249471 and 80ml for TC-5 249464.

 

 

Environment and labelling

Environmentally sound: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  European Aerosols comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Using instructions

Before use, carefully read and observe the warning texts on the label!

  • Clean the surface to be painted thoroughly with ColorMatic silicone cleaner no. 174469, then sand
  • Larger bare surfaces must be pre-primed with the appropriate ColorMatic primer
  • The area must be dry and free of dust and grease
  • Shake can vigorously for 2 minutes

Mixing A components with hardener:

  • Remove protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge.
  • The cartridge will then rotate 360 °, be completely open and release the hardener.
  • Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio.
  • Shake can vigorously for 2 minutes
  • Carry out spray test
  • Shake can vigorously for 2 minutes
  • Carry out spray test
  • Pot life: 24 hours (20 ° C)

Ready-to-use coating materials containing isocyanates can exert an irritant to the respiratory system and cause allergic reactions. Inhalation of vapours and spray mist is a risk of sensitization. When dealing with substances containing isocyanates all measures for solvent-based coatings are considered. In particular, spray mist and vapours are not inhaled. Allergy and asthma sufferers and people who are prone to respiratory diseases should not perform work with isocyanates materials.

 





Tips for spray painting

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

Technical manual 2K pre-fill HS Topcoat
Technical manual 2K pre-fill HS Topcoat
Technical manual 2K pre-fill HS Topcoat
Technical manual 2K pre-fill HS Topcoat
2 min
Technical manual 2K pre-fill HS Topcoat
Technical manual 2K pre-fill HS Topcoat
*
Technical manual 2K pre-fill HS Topcoat
*
Technical manual 2K pre-fill HS Topcoat
Technical manual 2K pre-fill HS Topcoat
 
 
 

*Pay attention to manufacturer's instructions/ Angaben des Lackherstellers beachten

 

Order information

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

There are no prdocuts to show.

Overview paint manufacturer

Technical manual 2K pre-fill HS Topcoat

Examples for use

Technical manual 2K pre-fill HS Topcoat
Technical manual 2K pre-fill HS Topcoat

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

De presto reparatie box met PE-hars, verharder, glasvezel doek en glasvezel fleece biedt je alles wat je nodig hebt voor goedkope maar doeltreffende...

Meer lezen

Lelijke deuken op vleugels of bumpers kunnen snel en gemakkelijk verwijderd worden met MoTip laksprays.

Meer lezen