Technical Information Sheet Wheel Spray

Technical Information Sheet Wheel Spray

ColorMatic velgenlak is een hoogwaardige acrylaatverf met een hoge dekking en een snellere droogtijd. De professionele breedstraalverneveling zorgt voor een uitstekende vloeiing en garandeert een positief resultaat.

Voor een optimale hechting moeten de aluminium wielen worden geprimerd met ColorMatic 1K Primer voor aluminium (Art. no. 190278). Stalen velgen moeten worden geprimed met ColorMatic 1K Primer Filler.

Toepassing:

Ideaal voor het spuiten van nieuwe of gebruikte velgen.

Quality and properties

  • Simple time-saving application
  • Fast drying time
  • Exceptionally high coverage
  • Resistant to stone chips, road salt, etc.
  • Abrasion resistant
  • Robust against damage during automatic car wash

Physikalische und chemische Daten

  • Basis of binder: NC
  • Colour: black (no. 190353), silver satin glossy (no. 190377)
  • Smell: solvent
  • Degree of gloss: (at measurement angle 60° acc. to DIN 67530)
    glossy: 80 gloss units
  • Efficiency:
    Depending on consistence and colour of the ground:
    400 ml are sufficient for approx. 0,8 - 1,0 m²
  • Substrate:
    Thoroughly cleaned, new or second-hand steel or aluminium wheel rim
  • Drying time (at 20°C, 50% relative air humidity):
    Dust-dry: after approx. 10 minutes
    Dry to touch: after approx. 30 minutes
    The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
  • Temperature resistance: to 80°C
  • Storage stability:
    10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
  • Size:
    Aerosol cans, maximum nominal volume 400 ml
  • VOC-value: 273,1g



Environment and labelling

Environmentally sound: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  European Aerosols comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Using instructions

Before use, carefully read and observe the warning texts on the label!

  • Clean the surfaces to be painted thoroughly with ColorMatic silicone cleaner no. 174469, then sand
  • The area must be dry and free of dust and grease
  • Shake can vigorously for 2 minutes
  • Carry out spray test
  • For optimum adhesion before application, the aluminium wheels can be primed with ColorMatic 1K primer for aluminium no. 180 278 - steel wheels with ColorMatic 1K primer filler
  • 2-3 coats

  • For professional use only
  • Wear an appropriate respirator (recommended type A2/P3)

Hints concerning application

Also suitable for coating exhaust tail-pipes.

Technical Information Sheet Wheel Spray
2 min
Technical Information Sheet Wheel Spray
2-3
Technical Information Sheet Wheel Spray
5 min
Technical Information Sheet Wheel Spray
20°C=60 min
Technical Information Sheet Wheel Spray
Technical Information Sheet Wheel Spray
 

Order information

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

There are no prdocuts to show.

Voorbeelden voor gebruik

Technical Information Sheet Wheel Spray
Technical Information Sheet Wheel Spray

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.

As of July 26, 2010
This release replaces all eventually earlier issued versions

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

Tot nu toe konden afgescheurde scharnieren van deuren, dressoirs, schappen en kastjes enkel door professionals hersteld worden…

 

Ook geschikt voor:...

Meer lezen

Zelfs schade aan metaal of metaalbladen kan gemakkelijk hersteld worden met presto Alu Metal Filler. De afgewerkte herstelling gaat mooi over in het...

Meer lezen