Technical information Pre-fill Standard without solvent

Technical information Pre-fill Standard without solvent

The ColorMatic pre-fill spray paint is prefilled with propellant and then filled by VitoMat filling machines with the desired coat. Innovative spray and valve technology guarantee the fine broad jet atomisation, a high application rate and constant pressure for best workmanship and professional-quality end results.

The ColorMatic pre-fill standard is a pre-filled can with propellant that can be filled with solvent-based basecoats.Application:Ideal for spot repairs or refinishing parts.

 

Quality and properties

  • A spray can pre-filled with propellant. The paint is transferred via a filling device into the can to produce a ready-to-use end product (dealers liability)
  • Simple, time-saving application
  • Excellent atomisation
  • Light blending


Ideal for spot or refinishing parts

 

Physical and chemical data

  • Colour: depending on filling
  • Efficiency:
    Depending on consistence and colour of the ground
  • Substrate:
    Depending on the colour of the substrate apply Primer Filler HG1 - HG8, 2K Primer Filler no. 195 327, 1K Primer for ALU no. 190 278, 1K Primer for Zinc no. 190 285, 1K Epoxy Primer no. 174 414, 1K Filler, beige no. 856 556, ColorMatic 1K Filler, grey no. 874 987, cured paint sanded
  • Drying time (at 20°C, 50% relative air humidity):
    The drying time depends on surrounding temperature, air humidity, thickness of the applied coat and the filled type of paint (refer to information of the paint manufacturer)
  • Storage stability: empty cans: 5 years
    Filled cans: depending on type of paint from several hours up to 6 month (information from your specialist dealer). If appropriate storage provided (=10°-25°C, relative air humidity max. 60%)
  • Size:
    Aerosol can, maximum nominal volume 400 ml, filling quantity up to 200ml
  • VOC-value: 110g

 

 

Environment and labelling

Environmentally sound: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  MOTIP DUPLI comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Using instructions

Before use, carefully read and observe the warning texts on the label!

  • Clean the surface to be painted thoroughly with ColorMatic silicone cleaner no. 174 469, then sand
  • Larger bare surfaces must be pre-primed with the appropriate ColorMatic primer
  • The area must be dry and free of dust and grease
  • Shake can vigorously for 2 minutes
  • Carry out spray test
  • Compatibility testing is necessary

  • For professional use only
  • Wear an appropriate respirator (recommended type A2/P3)
Technical information Pre-fill Standard without solvent
2 min
Technical information Pre-fill Standard without solvent
*
Technical information Pre-fill Standard without solvent
*
Technical information Pre-fill Standard without solvent
Technical information Pre-fill Standard without solvent

*Pay attention to manufacturer's instruction/ Angaben des Lackherstellers beachten

 

Order information

printing preview/further products

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

Products: The subpart part marker ###ITEM_LIST_EMPTY### or the template file EXT:snet_tmpl_motip/Resources/Private/Templates/Extensions/tt_products/products_template_en.tmpl has not been found.

Examples for use

Technical information Pre-fill Standard without solvent
Technical information Pre-fill Standard without solvent

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.

For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.

As of August 1, 2013
This release replaces all eventually earlier issued versions

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

Je kan een individueel waterlandschap voor je tuin creëren met presto special hars en glasvezelmatten. De diverse aard van steen, zand en keien...

Meer lezen

Kapotte randen kunnen snel weer aan elkaar gelijmd worden met de presto Bodyfiller, voor een langdurige stabiliteit.

 

Ook geschikt voor gebruik op:...

Meer lezen