Technical Information Zinc Primer

Technical Information Zinc Primer

Outstanding protection against corrosion for all iron metals, such as car bodies, exhaust systems, gates, machines, metal housings, metal fittings, fences etc. Especially suitable for the protection of welding seams and metals which are exposed to corrosion.

Cathodic rust-protection on a very high technical level, which is very easy and quick to apply.

For the colour-matching repair of zinc-plated surfaces, use DUPLI-COLOR Zinc-Alu-Spray art.no. 504433.

Quality and properties

  • Very easy and quick to apply cathodic corrosion protection for blank metals
  • High-grade zinc coating with more than 90 % zinc share in the dry film
  • Resistant to highest demands against corrosion
  • Highheat-resistant up to 600°C  
  • Particularly suitable for welding seams  
  • Ideal for all metals in outside places, which are liable to rust
  • Good flow
  • Coatable
  • For colour-matching repair of zinc-plated objects use DUPLI-COLOR Zinc-Alu-Spray verwenden

Physical and chemical data

  • Basis of the binde: epoxyester
  • Colour: grey
  • Smell: solvent
  • Degree of gloss (at measurement angle 60° acc. to DIN 67530):
    matt, 0-5 gloss units
  • Efficiency:
    Depending on consistence and color of the ground:
    400 ml are sufficient for approx. 1.0 - 1.5 m² at covering layer
  • Drying time (at 20°C, 50% relative air humidity):
    Dust-dry: after approx. 10 minutes
    Dry to touch: after approx. 20 minutes
    Can be exposed to heat: after approx. 8-12 hours
    The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
  • Temperature-resistant: up to 600°C
  • Storage stability:
    10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
  • Size: aerosol cans, maximum nominal volume 400 ml

Environment and labelling

Environmentally sound: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  MOTIP DUPLI comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Using instructions

The most DUPLI-COLOR spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the label!

Preparation of the ground:

  • The metal surface has to be blank and free from fat.
  • Due to the high density, the Zinc Primer has to be shaked for at least 2 minutes after you hear the noise of the mixing-balls. Otherwise the valve could block. 

Lacquering:

  • Shake the can vigorously for approx. 2 - 3 minutes.
  • Test spray at an invisible spot.
  • Apply several covering coats.
  • Spray from a distance of approx. 25 - 30 cm.
  • After drying (approx. 24 hours) apply primer and top coat.
  • Do apply just thin coats to objects, which are exposed to high heat. If necessary, re-coat with temperature-resistant lacquer (test painting).
  • Overpainting with other paints is not recommended.

Tips for spray painting

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

 

Order information

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

Products: The subpart part marker ###ITEM_LIST_EMPTY### or the template file EXT:snet_tmpl_motip/Resources/Private/Templates/Extensions/tt_products/products_template_en.tmpl has not been found.

Examples for use

Technical Information Zinc Primer
Technical Information Zinc Primer

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.

For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.

As of May 10,  2017
This release replaces all eventually earlier issued versions.

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

Met de ijzerhoudende DUPLI-COLOR Magnetic Paint voorkom je gaatjes door spijkers en resten van tape op je muren. De clou: je kan zelfs over de...

Meer lezen

Lelijke deuken op vleugels of bumpers kunnen snel en gemakkelijk verwijderd worden met MoTip laksprays.

Meer lezen