Technical Information Bodyfiller

Technical Information Bodyfiller
Technical Information Bodyfiller

presto Body Filler is a 2-component polyester filling putty as mixture of a medium-elastic, highly reactive, amino-preaccelerated polyester resin with different mineral, environment-friendly fillers.

Applicable on metal, wood, concrete. To fill holes and unevennesses, to rework pretreated surfaces during repair on car body parts and other metal surfaces, for reconditionning and restoration of wood or concrete surfaces, e.g. steps of stairs, fitting of anchor bolts and screws etc.

For universal use in the entire hobby and DIY sector. 

Localized corrosion holes with a diameter less than 12 mm, can be filled before with presto Fibre Glass Filler. Localized corrosion holes bigger than 12 mm diameter should be treated with the presto Repair Box.

For preparation and finishing your filling job, we recommend our presto sand papers. We offer a wide assortment of fine and coarse papers for dry and wet sanding.

Here you find the presto application video spot.

 

Quality and properties

  • Ease of working
  • Quick, time-saving handling
  • Very good adherence on different surfaces
  • Easy to sand, even after a longer period
  • Suitable for stoved enamel coating
  • Free of asbestos and silicone
  • Resistant to weak acids and bases, propellants, solvents, water and de-icing salt

Physical and chemical data

  • Basis: polyester resin with mineral fillers
  • Colour: ochre
  • Smell: styrol
  • Consistence: soft, thixotropic, pasty
  • Pot life / Working time at 20°C: approx. 5 - 6 minutes
  • Working temperature: min. 12°C
  • Drying time (at 20°C, 50% relative air humidity):
    can be sanded after approx. 30 minutes
  • Flash point:
    approx. 33°C (resin); not applicable for hardener
  • Density at 20°C:
    putty 1.85 g/cm³
    hardener 1.15 g/cm³
  • Addition of hardener: 2 - 4 % (optimal mixture 2,5 %)
  • Temperature resistance of the cured material: 120°C
  • Storage stability:
    18 months if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) in the unopened original container. Protect from direct sunlight, frost and humidity.
  • Packing:
    small ring tins; hardener: plastic tubes 

Environment and labelling

Environmentally sound: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  MOTIP DUPLI comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

 

Order informations

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

Products: The subpart part marker ###ITEM_LIST_EMPTY### or the template file EXT:snet_tmpl_motip/Resources/Private/Templates/Extensions/tt_products/products_template_en.tmpl has not been found.

Examples for use

Technical Information Bodyfiller
Technical Information Bodyfiller

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.

For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.

As of November 30, 2010
This release replaces all eventually earlier issued versions.

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

De ideale en goedkope manier om zeer sterke en hittebestendige metalen schakels te repareren met presto kleefstaal.

 

Ook geschikt voor gebruik op: ...

Meer lezen

Je kan een individueel waterlandschap voor je tuin creëren met presto special hars en glasvezelmatten. De diverse aard van steen, zand en keien...

Meer lezen