Technical information VitoMat II Pneumatic Filling Machine

Technical information VitoMat II Pneumatic Filling Machine

The ColorMatic VitoMat filling machines allow ColorMatic pre-fill spray paint cans (already containing propellant and specific additives) to be filled with individual paints. There are three different VitoMat filling machines to choose from, each offering advantages for different needs. All machines fill both 400ml and 150ml cans.

Detailed instructions of 150 ml and 400 ml and also for the CleanJector filling are applicable.

Application:
VitoMat II is ideal for filling medium to large volumes

Available colours/order numbers Search dealer for this product General Remarks

Quality and properties

  • Robust, stable machine, suitable for filling medium size orders
  • All important functions directly displayed and easy to read
  • Pressure regulators easy to use (working pressure 7-8 bar)
  • Portable, removable piston, which fits the cylinder
  • Compatible with CleanJector
  • No power supply required
  • Very easy to operate
  • Suitable for filling 400ml and 150ml cans
  • Suitable for filling 1K and 2K coating qualities
  • Suitable for water-and solvent-based coats
  • Fast colour change
  • Very good value for money

 

Physical and chemical data

  • Description: Exterior: Case made of stainless high-grade steel with door, operating controls and control display, base plate and compressed air condition; Interior: Mobile lifting device with stop plate, cylinder as paint receptacle and intended holding device, mobile piston and adapter for filling.
  • Measurements: 32 x 25 x 78 cm
  • System pressure: 7 - 8 bar
  • Working pressure: 6,5 bar constant
  • Capacity: approx. 35 cans/ h
  • Max. filling viscosity: 300 s/DIN 4 mm
  • Life: Long working life since there is almost no wear and tear

 

Environment and labelling

Environmentally sound: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  European Aerosols comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Using instructions

Before use, carefully read and observe the warning texts on the label!

  • The filling process is simple and can achieve high volume
  • For detailed instructions, please refer to the attached manual

  • For professional use only
  • Wear appropriate protection goggles and gloves

Hints concerning filling

To ensure a smooth filling process, the connected compressor must present a continuous operating pressure of 6.5 bar. The well visible pressure manometer will allow you to read the pressure at any time. If you use the intended base plate to bolt the VitoMat II firmly to the ground, working will be so much easier. The adjustable pedestals can be used to quickly stabilise the device.

 

 

Order information

 Color   Product   Bundle   Art.No. 
 CM VitoMat II pneum.Abfüllanl.   Stück   249792 

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

Examples for use

Technical information VitoMat II Pneumatic Filling Machine
Technical information VitoMat II Pneumatic Filling Machine

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.

As of October 16, 2013
This release replaces all eventually earlier issued versions.

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

De ideale en goedkope manier om zeer sterke en hittebestendige metalen schakels te repareren met presto kleefstaal.

 

Ook geschikt voor gebruik op: ...

Meer lezen

Hier kunt u gestileerde muurschilderingen in blad-patroon maken. De truc: de bladen worden niet geschilderd maar erop gespoten met stencil...

Meer lezen