Technical Information Bumper Spray

Technical Information Bumper Spray

With MoTip Bumper Spray, scratched and weathered bumpers are a thing of the past. It is used to repair and improve plastic bumpers while still maintaining the original structure. The spray can be directly applied to plastic surfaces without the need to prime and gives synthetic surfaces a silky shine.

The spray is available in 5 different colours to match the colour of the bumper.

Quality and properties

  • Long-lasting shine and colour
  • Keeps the bumper’s original structure
  • Scratch and shockproof
  • Easy to use
  • Fast drying time
  • Excellent coverage
  • Excellent adhesion
  • Suitable for many other synthetic materials

Physical and chemical data

  • Basis of the binder: alkyd resin
  • Colour: diverse
  • Smell: solvent
  • Degree of gloss: (at measurement angle 60° acc. to DIN 67530):
    satin glossy: 30-35 gloss units
  • Efficiency:
    Depending on consistence and color of the ground:
    400 ml are sufficient for approx. 2 bumpers
  • Drying time (at 20°C, 50% relative air humidity):
    Dust-dry: after approx. 20-30 minutes
    Dry to touch: after approx. 1 hour
    Overworkable: after approx. 24 hours
    The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
  • Temperature resistance: up to 110°C
  • Storage stability:
    10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
  • Size:
    aerosol can, maximum nominal volume 400 ml

Environment and labelling

Environmentally sound: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  European Aerosols comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Instruction manuel

Before use, carefully read and observe the warning texts on the label!

Application:

  • The surface must be clean, dry and free of grease.
  • Shake the can well for 2 minutes before use.
  • Spray to test compatibility on an inconspicuous area.
  • Keep spraying distance of ca. 25-30 cm.
  • Apply several thin coats until you have achieved the desired results.

Tips for spray painting

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

 

Order informations

 Color   Product   Bundle   Art.No. 
 Stoßstangenspray anthrazit 400   400 ml   04076 
 Stoßstangenspray dkl.grau 400   400 ml   04075 
 Stoßstangenspray grau 400   400 ml   04074 
 Stoßstangenspray schwarz 400   400 ml   04073 
 Stoßstangenspray weiss 400   400 ml   04085 

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

Examples for use

Technical Information Bumper Spray
Technical Information Bumper Spray

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.

As of: February 8, 2010
This release replaces all eventually earlier issued versions.

NIEUWS

Vorig jaar vond de opening van ons Experience Center in Wolvega plaats. Deze nieuwe locatie aan de overkant van het hoofdkantoor in Nederland is de...

Meer lezen

IDEEËN

Zelfs schade aan metaal of metaalbladen kan gemakkelijk hersteld worden met presto Alu Metal Filler. De afgewerkte herstelling gaat mooi over in het...

Meer lezen

Hier kunt u gestileerde muurschilderingen in blad-patroon maken. De truc: de bladen worden niet geschilderd maar erop gespoten met stencil...

Meer lezen